Garage Floor Screed · Somerset
Shepton Mallet Garage Floor Screed Specialists
Shepton Mallet garage conversions and new garages need a floor that's flat enough for a polyurea or epoxy finish — that's a job for liquid screed, not hand-trowelled mortar.
Get a fixed price for Shepton Mallet Garage Floor Screed Specialists
30 seconds. We'll come back same-day with a fixed price and next available date.
Or call our landline on 01392 237700
Shepton Mallet garage conversions and new garages need a floor that's flat enough for a polyurea or epoxy finish — that's a job for liquid screed, not hand-trowelled mortar.
Liquid screed over a garage slab leaves a surface flat enough for direct application of two-pack epoxy, polyurea or polyaspartic floor coatings — no further levelling compound required.
Most of our Shepton Mallet jobs sit within 30 minutes of base, so site visits stay simple and pour days run to time. Shepton Mallet sits Bridgwater (20 mi), and we work the surrounding villages on the same week's diary.
Common briefs across Shepton Mallet
- Georgian townhouses — a regular brief in Shepton Mallet
- Stone cottages — a regular brief in Shepton Mallet
- Small new-build estates — a regular brief in Shepton Mallet
- High-street shop retrofits — a regular brief in Shepton Mallet
- Independent retail — a regular brief in Shepton Mallet
Who this is for in Shepton Mallet
Shepton Mallet runs a healthy mix of residential renovation and small-to-medium commercial fit-out. We price both, and run both with the same fixed-price approach.
Garage Floor Screed in Shepton Mallet — how it works
A typical Shepton Mallet single-garage floor of 18-24m² is poured and finished in well under a morning, with the pump set up on the driveway.
We assess the existing slab, prep with shot-blasting or grinding where needed, lay edge isolation and a DPM if unbonded, then pump and level the screed in a single visit.
Materials and systems we use in Shepton Mallet
Cemfloor CT-C30-F6
Cement-based screed — robust, coating-ready surface.
Bonding primer
For bonded pours over existing slabs.
DPM and slip membrane
For unbonded over insulation or older slabs.
Shot-blasting / grinding prep
Where the existing slab needs surface profile.
What to expect on pour day in Shepton Mallet
- 1
Site visit — assess the existing slab, falls, thresholds
- 2
Prep: clean, prime or lay DPM and insulation
- 3
Pump and level in a single morning
- 4
Cover for 24 hours, walk-on by day 2
- 5
Coatings or floor finishes once dry — typically 7-14 days
Floors poured around Shepton Mallet
Other areas we cover near Shepton Mallet
Proof from the Somerset workload
Common Shepton Mallet build questions
What about cold garages — will it cure?+
We won't pour below 5°C. For winter jobs we'll either heat the space or schedule for a mild day in your Shepton Mallet diary.
Will it slope to a drain?+
Liquid screed self-levels — it won't form a fall. If you need a drain fall in your Shepton Mallet garage, we form it in the substrate first, then screed at constant thickness.
Can liquid screed take an EV charger and a car's weight in Shepton Mallet?+
Yes — a properly specified 40-50mm liquid screed easily handles domestic vehicle loads. We'll size the build-up to your Shepton Mallet garage usage.
Do you tidy up afterwards?+
Wash-out is bagged and removed. We leave the Shepton Mallet site clean and the floor protected with sheeting.
Can I finish the floor with epoxy?+
Absolutely — liquid screed gives you a flat, dense base that resin coatings bond to well once the screed is dry and the surface laitance is sanded off.
Can you do garage conversions as well?+
Yes — full conversion floors with insulation, UFH and screed in one coordinated package across Shepton Mallet and the surrounding area.
Talk to a Shepton Mallet-area screeder
We'll walk the build with you over a phone call — no hard sell, just honest numbers.
Ready to get a price?
Tell us the rough size and location — we'll come back with a fixed quote today.
Or call our landline on 01392 237700
Related on this site