Garage Floor Screed · Devon
Culmstock Garage Floor Screed Specialists
Culmstock garage conversions and new garages need a floor that's flat enough for a polyurea or epoxy finish — that's a job for liquid screed, not hand-trowelled mortar.
Get a fixed price for Culmstock Garage Floor Screed Specialists
30 seconds. We'll come back same-day with a fixed price and next available date.
Or call our landline on 01392 237700
Culmstock garage conversions and new garages need a floor that's flat enough for a polyurea or epoxy finish — that's a job for liquid screed, not hand-trowelled mortar.
Liquid screed over a garage slab leaves a surface flat enough for direct application of two-pack epoxy, polyurea or polyaspartic floor coatings — no further levelling compound required.
Most of our Culmstock jobs sit within 30 minutes of base, so site visits stay simple and pour days run to time. Culmstock sits Exeter (20 mi), and we work the surrounding villages on the same week's diary.
Where liquid screed earns its keep in Culmstock
- Stone farmhouses — a regular brief in Culmstock
- Barn conversions — a regular brief in Culmstock
- Cottage extensions — a regular brief in Culmstock
- Occasional new-build cottages — a regular brief in Culmstock
- Agriculture — a regular brief in Culmstock
Built for Culmstock rural self-builders and farms
Culmstock sits rural — barn conversions, self-builds, agricultural sheds, equestrian floors. Access is usually fine, but power and water on site need confirming up front. We do that at the site visit.
Garage Floor Screed in Culmstock — how it works
A typical Culmstock single-garage floor of 18-24m² is poured and finished in well under a morning, with the pump set up on the driveway.
We assess the existing slab, prep with shot-blasting or grinding where needed, lay edge isolation and a DPM if unbonded, then pump and level the screed in a single visit.
Cemfloor systems for Culmstock
Cemfloor CT-C30-F6
Cement-based screed — robust, coating-ready surface.
Bonding primer
For bonded pours over existing slabs.
DPM and slip membrane
For unbonded over insulation or older slabs.
Shot-blasting / grinding prep
Where the existing slab needs surface profile.
Step-by-step for a Culmstock job
- 1
Site visit — assess the existing slab, falls, thresholds
- 2
Prep: clean, prime or lay DPM and insulation
- 3
Pump and level in a single morning
- 4
Cover for 24 hours, walk-on by day 2
- 5
Coatings or floor finishes once dry — typically 7-14 days
Floors poured around Culmstock
Adjacent areas — usually same-week diary
Proof from the Devon workload
Common Culmstock build questions
Will it slope to a drain?+
Liquid screed self-levels — it won't form a fall. If you need a drain fall in your Culmstock garage, we form it in the substrate first, then screed at constant thickness.
Do you tidy up afterwards?+
Wash-out is bagged and removed. We leave the Culmstock site clean and the floor protected with sheeting.
What about cold garages — will it cure?+
We won't pour below 5°C. For winter jobs we'll either heat the space or schedule for a mild day in your Culmstock diary.
Can I finish the floor with epoxy?+
Absolutely — liquid screed gives you a flat, dense base that resin coatings bond to well once the screed is dry and the surface laitance is sanded off.
Can liquid screed take an EV charger and a car's weight in Culmstock?+
Yes — a properly specified 40-50mm liquid screed easily handles domestic vehicle loads. We'll size the build-up to your Culmstock garage usage.
Do you need to remove my existing garage floor?+
Usually no — if the existing slab is sound we bond directly to it from 30mm. We'll inspect first at the Culmstock site visit.
Ready for a laser-flat floor in Culmstock?
Send us the floor area, build-up and target dates — we'll come back with a fixed quote and a date.
Ready to get a price?
Tell us the rough size and location — we'll come back with a fixed quote today.
Or call our landline on 01392 237700
Related on this site